| POND CONSTRUCTION MATERIALS |
422 East Columbia Drive
Kennewick Wa. 99336
Technical Help / Orders (509)-586-1945
Orders only 1-800-497-3627 24 hours a day
|
FOR GREATER SAVINGS CHECK OUT OUR BARGAINS PAGE All sales Final! No Returns on sale Merchandise |
 |
 Pond guard
EPDM POND LINERS |
|
Prices Reduced!
EPDM LINERS- KOI JOY's aquaculture grade 45 mil and 60 mil EPDM rubber
liners are manufactured in the USA by Firestone, the largest producer of
aquaculture grade pond liners. Recognized world wide as the best and easiest
way to build a pond, Firestone's EPDM Pond guard liner is the
most commonly used material available today. While heavy enough to endure
against tears and punctures, this material is flexible to enable it to
conform to your ponds walls and corners. This is the easiest way to build
a pond of any size. Simply dig the hole, measure it, order materials, and
when it arrives, unroll and place. This liner carries a 20 year warranty
and is more resistant to tears and punctures than other liner materials.
Available in 45 mil, it can be glued and taped together to form
a stream or waterfall leading into pond. We recommend use of SEAM SEALER
KIT 03-SEAMKT (includes 25 ft of tape, 16 oz. seam sealer, brush, roller, etc.
for double seam sealing and leak protection. Purchase cut liner in widths of either 5 1/2', 10 ft, 15 ft, 20
ft, 25 ft, and up to 50 ft wide, and in lengths of 100 ft long. Because liner is manufactured in multiples of 5 ft width, it must
be sold in one of those widths. 45 mil cut liner cost is $0.69/ft2 plus
freight. Whole rolls
of 45 mil liner cost $0.64/ft2 plus freight.. Rolls are available in 100 ft
long, etc.There is an
additional charge for residential delivery, lift gate fees,
etc. Residential fees vary from $30 to $75 depending on local area.
JOINING LINER FOR STREAMS OR WATERFALLS When joining two liner sections together, as when attaching a waterfall or stream to a pond, use seam prep 03-SEA16 to clean mating surfaces, 03-TAPE23 or 03-TAPE26 to join along together, with caulk 03-BCAU16 if desired, then cover seam with 03-TAPE6B for insurance against leakage. We recommend at least two methods and preferably 3, for sealing against leaks when under water pressure or if the seam will be difficult to reach for repair of any leaks. PENETRATING LINER WITH PIPE
Pipe boots 03-PBKIT2 or 03-PBKIT5 are used to seal pipe joint where it penetrates liner. Pipe is inserted through liner, liner surrounding pipe is cleaned with liquid seam prep 03-SEAM16 (not included with boot), and boot tip is cut off to fit pipe (boot is in conical shape with built-in self-sticking flange). Pipe at penetration is covered with caulk 03-BCAU16 (not included with pipe boot), boot is slid onto pipe, paper backing is removed from boot flange, then boot is pressed onto liner to seal. Finally, clamp (included with pipe boot) is installed onto boot tip, and tightened to seal boot to pipe.
LINER ACCESSORIES, TABLE A
|
Pond Guard Pond Liner Full Rolls of EPDM Pond Guard pond liner are available in the following full roll sizes. These can be shipped by freight truck direct to your home or business. Shipping weights are shown on each roll size available. Cost is calculated at $0.64 per sq. ft. Cost indicated does not include delivery charges which will be added at time of order. There is an additional $35 to $75 delivery charge to all residential areas, added by the freight company.
FULL ROLLS, TABLE C
Pond Gard FireStone *
45 mil, EPDM Pond Liner
| ITEM # | SIZE | SQ. FT. | WEIGHT | COST* at $0.64 / sq ft |
| 03-55X100 | 5.5' X 100' | 550 | 165 LBS | $352.00 |
| 03-10X100 | 10' X 100' | 1000 | 330 LBS | $640.0 |
| 03-15X100 | 15' X 100' | 1500 | 480 LBS | $960.00 |
| 03-20X100 | 20' X 100' | 2000 | 640 LBS | $1280.00 |
| 03-25X100 | 25' X 100' | 2500 | 790 LBS | $1600.00 |
| 03-30X100 | 30' X 100' | 3000 | 900 LBS | $1920.00 |
| 03-35X100 | 35' X 100' | 3500 | 1090 LBS | $2240.00 |
| 03-40X100 | 40' X 100' | 4000 | 1200 LBS | $2560.00 |
| 03-50X100 | 50' X 100' | 5000 | 1550 LBS | $3200.00 |
|
Use our 45 mil EPDM liner for the pond and for the water fall/stream system. Basically, dig a hole for the pond and stream bed and measure the hole with a flexible rope or tape as follows: measure pond liner size: To measure the width, start 1-2 feet outside the widest section of the hole, and run the tape down into the hole and out the opposite side to one -2 feet beyond the hole. Then repeat to measure the other direction for length. Note: If the hole is curved like a crescent or "C", generally follow the shape of the hole, i.e. measure the length of the hole as it curves. Cut off extra material for waterfall or stream beds. Leave at least a foot or preferably two feet of extra liner all the way around, then order the liner. Use our pond under-layment to line hole for liner protection. You may also use old carpeting, newspapers, sand, or other material if necessary to protect liner from sharp rocks, tree roots, etc. When liner arrives, roll it out and lay it down in the hole. The black rubber material can get very hot on a summer day so use caution when touching. Use at least two of our seaming materials, i.e.. butyl caulk + double backed seaming tape, single sided tape, etc. to assure non-leaking seams. Stack or position rocks, sod, plants etc. around pond to conceal liner edges. Extra liner trimmed off previously can be used to double up the liner at places where large rocks are to be placed. seam liner sections: Seaming of two or more liner sections into one piece may be accomplished by use of our seaming kit 03-SEAMKT. This kit includes 25 ft of 3" double backed tape, 1 pint of liquid seam prep 03-SEAM16 which is required for a good seam, brush, pads, and a roller. Follow cleaning directions in Seam Kit 03-SEAMKT to assure removal of talc, dirt, grime, etc from liner. It is imperative that the rubber liner be absolutely clean prior to use of seaming tape or caulk. Order one kit for each 25 ft of seam. Butyl caulk 03-BCAU16 is recommended to improve the seam and to act as a second and backup sealing mechanism. Finally, clean and cover the actual seam with a 6" batten strip 03-TAPE6B to assure a permanent leak-proof seam. Order the length of the batten strip needed. Alternately, when joining two liner sections together, as when attaching a waterfall or stream to a pond, use seam prep 03-SEAM16 to clean liners, 03-TAPE23 or 03-TAPE26 to join along with 03-BCAU16 caulk along edge if desired, then cover seam with 03-TAPE13 or 03-TAPE16 for insurance against leakage. We recommend at least two methods and preferably 3, for sealing against leaks when under water pressure or if the seam will be difficult to reach for repair of any leaks. PATCHING LINER : Use 03-PAT6IN patches to permanently fix small tears or cuts (3-4" or less). Clean new liner with seam prep 03-SEAM16 to remove talcum and allow best possible repair. Alternatively, for larger patch jobs, use a section of liner attached to torn section with double backed tape 03-TAPE23 (3" wide) or 03-TAPE26 (6" wide) and the seam edge covered with single backed tape 03-TAPE13 or 03-TAPE16 for added reliability. Use our bottom drains (03-BDL300 or 03-BDL400 below) and local 3" PVC pipe to
supply your pumps. It is preferred to install the pumps dry, below the
water level to assure they stay primed. You should plumb a strainer basket
or trash basket such as our DRUM STRAINER DSL-1 before the pump
to protect it from leaves and trash. Your bio-filter could be located to
supply a waterfall and stream. To reduce energy costs, you should minimize
the height of any waterfall and stream and use a low energy pump Superfalls
pump such as the SUPERFALLS KJ4000LH.
STATIC HEAD HEIGHT: Static head height is measured from the surface of the pond to the height
where the water is pumped to. In other words, even if your pump draws from
the bottom of a 6 foot deep pond and pumps another 6 feet, the water is only being moved
6 feet from the surface of the pond to the level where it is discharged.
We recommend that you attempt to minimize the height, distance, and turns,
elbows, etc. that your pump must move the water through. Another way of
reducing head loss, is to use larger diameter piping wherever possible.
Plan to use 2" or 2 1/2" suction and discharge pipe for each pump and to use
3" or 4" plumbing where multiple pumps combine or when moving the water
long distances. A waterfall 10 ft high will require
a larger pump and thus more energy to supply than a 2 to 4 ft waterfall
or stream. We have seen some nice looking waterfalls with elevation changes
of only 1 to 3 foot. For very large waterfalls, up to 10' 12' high, use our
largest low head Superfalls pumps "Hi-Per" models with flows to 11,000
gallons per hour flow.
If you are building a large pond, we recommend that you consider use of two or more pumps rather than attempting to get full flow with a single pump. Multiple pumps offer some real benefits besides just energy savings. For example two KJ4000LH pumps can provide from 120 to150 gpm at only 4.6 amps at 1-5 ft head. To get the same flow from one large medium head pump would require 3-4 times the energy consumption. Multiple pumps also allow you a measure of insurance against loss of flow (and thus protection of fish) and allow you to shut off one or more pumps for more energy efficient winter or night-time operation. Note: bio-filters require 24 hr flow for proper operation. Our medium head Superfalls pumps can supply flows to 225 gpm. You should determine the flow you need and use two or more pumps to achieve that flow at the head pressure required. Your initial cost to purchase multiple pumps will be slightly more, but this extra cost will be returned to you many times over in electrical savings and peace of mind. We suggest that when building a pond, there are three places which you should insist on the best. First is of course the EPDM liner. Second would be to select the most energy efficient of the pumps that meet your requirements. Third, don't attempt to minimize the importance of a high performance bio-filter. |
|
BOTTOM DRAINS | |
Our 4" drain, the 03-BDL400 has a side 4" outlet for 4" pipe, flange, flange plate, and a domed cover for liner ponds. This drain can also be used in concrete if necessary although designed for liner ponds.
The 2" drains are available in liner model 03-BDL200, or concrete model, 03-BDC200. The liner model is installed in the pond so that the top of the unit without grate is flush to the bottom of the pond. liner is placed in the pond, cutout made for the drain, and grate screwed into place. The concrete model is simply installed onto the drain pipe and then concrete is poured over it until flush with the top. The 2" liner and concrete models have two different outlets, a 2" and a 1 1/2" outlet. Either, or both can be used to increase the drainage and flow. The concrete model includes a removable grate.
Two or more bottom drains are recommended in medium to large ponds for safety and increased flow characteristics.
Use our Portable Main drain 03-PBDL20, black, to add a bottom drain to
existing ponds without cutting liner or concrete. Uses 2" pipe, rests
on pond bottom and no penetrations required. Pump sucks directly from this drain
from over the side, or can be connected to our giant leaf trap 03-KJLCT3
or 03-KJLCT4 below (pump then draws water from it). Can also be used with
portable skimmer item # 03-PSKL15 to add skimmer to pond with no
penetrations.
|
|
HOSENCLOSE | |
 |
HosEnclose consists of a
high-density polyethylene enclosure, a 40-ft. or 60-ft coiled garden hose,
a spray nozzle and PVC plumbing, all provided in one complete package.
HosEnclose is installed below ground level anywhere in the yard with only
the lid exposed. Simply open the hinged lid to access the hose
and water. When closed, the lid will support foot traffic. The PVC plumbing assembly (piping and water valve) is all built-in, ready for connection to a water line. Adding one or more to a landscape irrigation system is simplified with the included 1/2” PVC union connector. Homeowners will find a HosEnclose handy near potted plants or on either or both sides of the pond, the patio for quick cleanups and the driveway to wash the car. By eliminating unsightly hose clutter, HosEnclose avoids the chance of accidental tripping. In addition, the polyurethane hose will last longer due to limited exposure to the sun’s deteriorating UV rays. The nozzle features a comfortable urethane grip and eight adjustable spray patterns. 03-HOSEC40 40' LENGTH $224.99 03-HOSEC60 60' LENGTH $286.99
|
|
WATER LUBE | |
|
|
Water Lube is perfect for home and marine use, automotive and industrial, pools and spas, as well as sporting equipment. Use on windows and sliding doors, water pumps and filters, hinges and latches, bicycle chains and roller skates, faucets and valves, yard equipment and wagon wheels, hunting and fishing equipment, and hundreds more applications where parts and materials are exposed to water and moisture. 03-WTRLUBE 1.75 ounce $3.99
|
Ultra-Mark™ Paint Applicators
 |
Inverted spray valve. Bright
fluorescent colors formulated to generate superior brilliance for long
range visibility. 2 colors available: Fluorescent Orange and Pink. |
03-PNTORG $5.99 03-PNTPINK $5.99 |
Rolla-Marker Paint Applicator
|
|
Paint applicator on a wheel saves
bending over to spray. Made of tough injection molded A.B.S. plastic with
chrome plated metal handle. Uses spray cans with inverted spray tip only. |
|
WATER PROOF SILICONE SEALANTS | |
 |
Mckanica Marine silicone sealants are an excellent
choice for sealing bottom drain gaskets, skimmer attachments, and other
under water applications. The pressurized can allows reuse of unused
silicone at later dates. The easy to use operating valve makes this an
essential item to have on hand when building your pond or performing
other work around the house.
Available in Black, Clear, or White. Do not attempt to seam liner with silicone. |
|
| Catalog # |
Item |
Color | Size | Cost ea. |
| SILBLK | Black Silicone Sealant | BLACK | 16 oz | $12.99 |
| SILWHT | White Silicone Sealant | WHITE | 16 oz | $12.99 |
| SILCLR | Clear Silicone Sealant | CLEAR | 16 oz | $12.99 |
| |
DRUM/STRAINER-LEAF TRAP | |
Now you won't have to worry about leaves plugging up your pump or your skimmer. When it fills with leaves or algae, simply pull it out, rinse out with garden hose and return to drum. It's simple slip fit makes removal and replacement easy and painless. Plumb your centrifugal pump directly to the drum with one of our bulk head fittings (not included) for strained water or simply place a submersible pump into the drum with its hose leading to your filter. A simple yet effective way to decrease your pond maintenance duties and protect your koi!
| Dimensions: |
| 35'' tall from lid to elbow (elbow not included) |
| 27'' wide at top of drum |
|
Basket Dimensions: |
| 24'' high x 18'' in diameter |
03-SPLCT3 leaf collection trap with large removable
strainer basket, 3" inlet $299.99
03-SPLCT4 leaf collection trap with large removable
strainer basket, 4" inlet $399.99
03-SPLCB3 Extra leaf collection basket, with 3" inlet
$99.99
03-SPLCB4 Extra leaf collection basket, with 4" inlet
$129.99
03-SPLBFM Extra leaf basket filter media
$33.99
|
|
New! SAVIO SkimmerFilters |
|
SkimmerFilter base unit. Has two built-in UV ports, skimmer basket, filter for ponds to 1000 gallon size. Base Unit and one Weir Inlet are priced and sold separately. UV's Optional and extra as shown. |
Savio has changed the way we build ponds with its new SkimmerFilter combo. The SkimmerFilter base unit can take care of skimming ponds to 8000 gallons with flows to 8000 gph. Internal ports (2) allow for the addition now or later of two UV sterilizer units. These are the easiest UV's to clean - simply twist to unlock, remove, wipe, and reinsert. No screws, or anything to take loose to clean. A large trash basket collects leaves and trash for simple removal. The SkimmerFilter has a built-in filter pad which is purported to be able to handle ponds to 1000 gallons. Anything larger should have a supplemental bio-filter. Three different size skimmer weir inlets are used for different sized ponds or flows. Order the base unit, and the appropriate weir inlet for your pond. This wonderful skimmer can be installed in concrete ponds or liner ponds. The extremely strong unit comes with a very strong lid, which is strong enough to be walked on, easily supporting a couple of football players (if necessary). Note: Savio has now replaced all UV Sterilizers with their new model (INEX), which does not require the use of a sleeve, but requires a new model of UV mount, new transformers, and of course new lamps. See New! below.
|
|
|
New! SAVIO Filters |
|
Select the filter to fit your construction plans. The model F100 has a 22"
waterfall curtain weir and creates an instant waterfall. Pond liner attaches to
the front of the filter under the curtain weir to direct flow to the pond.
Model F200 allows a different way to direct your filtered flow to a distant waterfall or directly back to the pond. The F200 offers you a chance to hide it in a remote location, ie. behind a building, shrub, etc. and pipe the water where ever you want. The 2" pipe discharge fitting allows you to attach a male adapter (not supplied) and pvc pipe directly to the filter to deliver the water wherever you want. Flow exits the filter through the bulk head fitting, down an elbow through approximately two feet of pipe, then continues via another elbow toward the pond or waterfall.
Both models come with one box of Spring Flo filter media and a top polishing filter mat to remove the finer particles. Both models come with a very strong lid, capable of supporting the weight of a very large person without damage.
Remote Model
| 04-SAV100 | SAVIO SPILLWAY FILTER, 22" | 5,000 gph max | $499.99 |
| 04-SAV200 | SAVIO PIPED REMOTE FILTER | 4,000 gph max | $499.99 |
| 04-SAVTPM | SAVIO TOP POLISHING MAT (Replacement) | $19.99 | |
| 04-SFFM01 | (Extra) Spring Flo Bio Media, Roll | $69.99 | |
|
SKIMMERS | |
Model 03-SSKLIN is a liner model skimmer which comes with a flange, gasket, and cover plate to seal against the liner. Model 03-SSKCON is designed for concrete use and otherwise is essentially the same.
Model 03-PSKL15 is
designed to be added to an existing pond with no skimmer and when you don't want
to cut liner or concrete. Go over the side with 1 1/2 inch pipe, angle upwards
into the bottom of this floating skimmer. You can also install a portable bottom
drain, 03-PBDL20 above, and use a "Tee" to add this
portable skimmer to your pond. Now your pump draws water off the bottom of the
pond and off the surface with leaves trapped in the skimmer basket!
03-SSKLIN |
Surface skimmer, liner | $119.99 |
| 03-SSKCON | Surface skimmer, concrete | $109.99 |
03-PSKL15 |
Portable surface skimmer, black, 1 1/2 inch outlet, rated at 20 - 55 gpm flow, can be used with 03-PBDL20 above. | $99.99 |
We are pleased to introduce the Easy
Pro Mini Pond Skimmer. Mini Skimmer - Skims ponds up to 250 sq. ft. Easy Pro Mini skimmer now comes
standard with "sandstone brown" lid and aluminum bolts and
washers. Handles pumps up to 50 GPM Dimensions are 20" long, 15" wide,
and 19" tall. 6" wide water inlet. Can be used with small extension tube!
04-MINISKM
Easy Pro Mini
Pond Skimmer
$285.00
|
TANK "BULK HEAD" FITTINGS | |
Plastic
fittings and washers which are used to attach pipe, valves, etc. to tanks,
drums, pond liners, swimming pools, etc. Available in 2" for top and 1.5"
for drain as used in UFF-1000 below. Use 03-BHF020 for drum outlet and
03-BHF150
for drain (includes plug). Use 3" and 4" bulk head fittings in the bottom
or side of liner ponds for drains and for penetrations. Bulk head fittings
come with one gasket. Additional gaskets can be made from left-over pond
liner material. These bulk head fittings are threaded inside and outside.
|
UNISEAL
GROMMETS FOR TANK PENETRATIONS
NEW!
A lower cost way to attach pipe of all sizes to tanks. This rubber grommet
is easily slipped into a hole cut with standard hole saws from outside
the tank. Once Uniseal is slipped into place with dishwashing soap, standard
PVC, or metal pipe can be pressed into grommet making a water tight seal
for water tanks, filters, etc. Uniseals are available in standard sizes
and cost approximately 1/2 the cost of the larger bulk head fittings.
| ITEM # | PVC PIPE SIZE | HOLE SAW SIZE | COST |
| 03-UNI050 | 1/2" | 1.25" | $5.99 |
| 03-UNI075 | 3/4" | 1.25" | $5.99 |
| 03-UNI100 | 1" | 1.75" | $7.99 |
| 03-UNI150 | 1 1/2" | 2.5" | $7.99 |
| 03-UNI200 | 2.0" | 3.0" | $10.99 |
| 03-UNI300 | 3.0" | 4.0" | $12.99 |
| 03-UNI400 | 4" | 5.0" | $15.99 |
| 03-UNI600 | 6.0" | 7.0" | $25.99 |
|
HOLE SAW KIT | |
A great buy just when you need it! These two hole saw kits
contain all of the sizes you'll ever need including the large ones
that are hard to find and very expensive, i.e.. up to $60 each! Small kit includes eight most common sizes from 3/4", through 2
1/2" saws, 1/4" and 3/8" mandrels, a 1/4" bit, a hex wrench, and carrying
case. Large kit includes 2 1/2", 3", 3 1/2", 4", 5", a 3/8" mandrel,
drive plate, hex wrench, and a convenient plastic carrying case.
03-HSKIT2 Eight most common sizes from 3/4" to 2 1/2" $32.99
03-HSKIT5 Five sizes from 2 1/2" to 5"
$39.99
|
|
FERNCO RUBBER COUPLERS & FITTINGS | |
COUPLERS & REDUCERS
 These
are sometimes the only answer to an easy way to connect a pump to a hose,
pipe, or penetration. The stainless steel bands make a water tight seal
and are impervious to water damage. These can be connected and then buried
in the ground without worry. Pipe Sizes are for C.I. and Plastic |
||||||||
| Part No. | Description, Pipe Size |
Side A |
Side B | Width C | Cost each | |||
| inches | mm | inches | mm | inches | mm | |||
| FC125-125 | Coupler 1 1/4" | 1.65 | 40 | 1.65 | 40 | 3.50 | 88 | $5.99 |
| FR150-125 | Reducer 1 1/2" to 1 1/4" | 1.90 | 48 | 1.65 | 40 | 3.50 | 88 | $5.99 |
| FC150-150 | Coupler 1 1/2" | 1.90 | 48 | 1.90 | 48 | 3.50 | 88 | $5.99 |
| FR020-150 | Reducer 2" to 1 1/2" | 2.40 | 60 | 1.90 | 48 | 3.50 | 88 | $7.99 |
| FC020-020 | Coupler 2" | 2.40 | 60 | 2.40 | 60 | 3.50 | 88 | $6.99 |
| FR030-020 | Reducer 3" to 2" | 3.38 | 85 | 2.40 | 60 | 4.00 | 101 | $7.99 |
| FC030-030 | Coupler 3" | 3.38 | 85 | 3.38 | 85 | 4.00 | 101 | $8.99 |
| FR040-030 | Reducer 4" to 3" | 4.38 | 111 | 3.38 | 85 | 4.00 | 101 | $11.99 |
| FC040-040 | Coupler 4" | 4.42 | 112 | 4.42 | 112 | 4.00 | 101 | $10.99 |
| FC050-050 | Coupler 5" | 5.62 | 142 | 5.62 | 142 | 4.00 | 101 | $16.99 |
| FC060-060 | Coupler 6" | 6.38 | 162 | 6.38 | 162 | 6.00 | 152 | $21.99 |
| Qwik Caps offer a quick, easy way to cap pipe ends,
cleanouts and open test
pipes. Made of flexible PVC, they're suitable for above-ground or
underground use, on cast iron, steel, copper, or plastic piping.
Qwik Caps are designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten band to 60" lbs. torque. |
|||||||||||||||||||||||||
| Qwik Caps offer a quick, easy way to cap pipe ends, cleanouts and open test
pipes. Made of flexible PVC, they're suitable for above-ground or
underground use, on cast iron, steel, copper, or plastic piping.
Qwik Caps are designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten band to 60" lbs. torque. Pipe Sizes are for C.I. and Plastic.
|
| ||||||||||||||||||||||||
|
SUPER SWIVELS | |
 A1 |
 A2 |
 B1 |
 B2 |
The Super Swivel is manufactured from schedule 80 PVC. The Swivel's operate on a ball bearing that is sealed on both sides and packed in grease to protect it from harsh elements. The Super Swivel life span is many times that of standard steel swivels. The Super Swivels are manufactured in sized 4'', 6'', 8'', 10'' and 12''. The 12'' is special order only. The pictures A1 and A2 show the Super Swivel using 90* elbows so that the stand pipe will lay horizontal out into the pond from the levee. In the pictures B1 and B2 they show the swivel using one 90 elbow so that the stand pipe will lay in the pond parallel to the levee.
The Super Swivel can be fitted to schedule 40 or 80 PVC. It can also be fitted to other PVC pipe with the use of fittings. It can also be fitted to steel pipe. The Super Swivel can be easily installed in minutes without welding-just glue to pipe going through levee.
For more information please feel free to call.
| 03-SWVL04 | 4'' SWIVEL | $530.99 |
| 03-SWVL06 | 6'' SWIVEL | $545.99 |
| 03-SWVL08 | 8'' SWIVEL | $702.99 |
| 03-SWVL10 | 10'' SWIVEL | $886.99 |
| 03-SWVL12 | 12'' SWIVEL | $1167.99 |
Why continue to suffer with frequent leaf trap cleaning, when you can stretch
that chore out to as little as 1/8 as often. With the SuperTrap inline
leaf trap, you can sit back and enjoy your pond instead of going out every day
to empty that little trap that you have.
Daryl is holding the long basket from our "upflow" model of the SuperTrap in one hand, and the much smaller typical trap in use by most pond owners. Our new basket holds up to 8 times a much of the waste material as that little one, and will offer much less resistance to flow than that little one, giving you more flow, less work, and the time that you want to enjoy your work.
The upflow model 04-UFST44 of our 6" SuperTrap, has a 4" inlet which can be connected directly to the 4" pipe which comes from your 4" bottom drain, and can also be connected directly to skimmers. This unit has a huge 6" removable lid in it's top which can also be used to prime your pump and system if desired. The 4" outlet to the pump is near the top and and provides clean strained water to the pump. The assembly is provided with 4" connections at the bottom (inlet) and at the top (outlet to the pump). The basket is approximately 44" long.
Our Down flow model of SuperTrap should be available soon, with it's inlet near the top, outlet to the coming out of the bottom and rising to the top. This model may be easier to install in earth that is compacted and rocky. It allows for the inlet pipe to be near the surface.
Our Back Flush Assembly 04-STBFA4 allows you to clean your leaf trap without removing the basket. When two three way valves are repositioned, the waste is flushed onto the ground, or into our French Drain Assembly 04-STFDA4 with it's drainage and collection basket. When the collection basket has drained, just empty it into the garbage can.
| ITEM NUMBER | SIZE | COMMON USE | COST |
| 04-STUF44 | 44" LONG | UP FLOW MODEL OF SUPERTRAP, 44" LONG BASKET IN 6" HOUSING | $429.99 |
| 04-STDF44 | 44" LONG | AVAIL SOON! DOWN FLOW MODEL OF SUPERTRAP, 44" LONG BASKET IN 6" HOUSING | $449.99 |
| 04-STBFA4 | 4" PVC | BACK FLUSH ASSEMBLY, 4" PVC PIPE WITH TWO 4" CHECK VALVES | $329.99 |
| 04-STFDA4 | 4" INLET | PERFORATED FRENCH DRAIN DRUM, BASKET AND LID. 4" INLET | $499.99 |
| 04-STXB44 | 44" LONG | EXTRA BASKET FOR UPFLOW OR DOWNFLOW MODEL OF 44" SUPERTRAP | $89.99 |
|
PVC VALVES | |
BALL valves are best used in places where you may have to regulate your
water flow or shut it off. These ball valves are manufactured in the USA
of the highest grade of materials to be smooth operating. They offer very
little resistance to flow, and are long lasting. Use these valves for adjusting
flow instead of gate valves (typically used as isolation valves). Available in 5
sizes.
|
|
CHECK or FOOT valves are used in discharge or suction lines to keep the line full of water. They are commonly used on the suction side of a centrifugal pump to maintain primed conditions. When a leaf trap is installed on the suction of a pump, the check valve must be installed so that the pump will remain full. This usually means in the suction line before the leaf trap. There is a very slight restriction in check valves so that a 2" check has the same flow as if 1 3/4" in size. If you must have no head loss, use the next larger size available. All check valves are slip/slip and white except models 03-CVTU15 and 03-CVTU20 which are clear true union swing checks. This allows visual assurance of primed conditions (pipe full of water) and removal for repair if necessary.
SWING CHECK (03-CV100S-300S) SWING CHECK TRUE UNION SWING CHECK
CLEAR OR OPAQUE
| 03-CV075T | SWING CHECK VALVE THREADED | 3/4'' | $12.99 |
| 03-CV100T | SWING CHECK THREADED | 1.0" | $13.99 |
| 03-CV150S | SWING CHECK, SLIP | 1.5" | $14.99 |
| 03-CVTU15 | TRUE UNION SWING CHECK, CLEAR | 1.5" | $22.99 |
03-CV200S |
SWING CHECK VALVE | 2.0" | $24.99 |
|
03-CVTSS2 |
CLEAR 2'' CV SLIP/SLIP | 2'' | $26.99 |
|
03-CVTU2 |
TRUE UNION SWING CHECK, CLEAR |
2" |
$31.99 |
| 03-CV300S | SWING CHECK VALVE, SLIP | 3.0" | $38.99 |
| 03-CVC300 | SWING CHECK, SLIP, CLEAR | 3.0" | $48.99 |
| 03-CV400S | SWING CHECK, SLIP | 4.0" | $55.99 |
| 03-CVC400 | SWING CHECK, SLIP, CLEAR | 4.0" | $69.99 |
|
6'' BACKWATER VALVE | |
 |
* Available in PVC * Gasketed flapper insures a water tight seal * Flapper design allows for unrestricted flow of effluent * Made of corrosion free materials to assure inside remains smooth without flaking and pitting * Used in nominally horizontal drain lines and branches * All hubs are DWV (schedule 40) * 10''D x 11''H x 16''L |
| 03-BWTRV6 | 6'' backwater valve | $179.99 ea. |
|
New! SADDLE TEE | |
 |
Saddle Tee's offer the fastest and easiest way to tap into your existing system. Saddle Tee's have a unique plastic wedge that allows for a simple installation. The wedge can be applied half way by hand and finished off by a slight tap of a rubber mallet. The wedge also equally distributes the clamping force over the entire saddle while giving full support along the axis of the pipe. Saddle Tee's eliminate the need to cut pipe when an upgrade is necessary.
|
|
New! 3-WAY DIVERTER VALVE | |
 |
We are pleased to introduce our new 3-way diverter valve. The 3-way valve is designed to be able to divert water anywhere diversion is required. The diverted seals are made of special lubricated EPDM material. Every Flo valve can be easily adapted to automatic valve actuators, adaptation available soon.
|
|
UNIONS | |
Half Unions are used to connect to a buttress fitting or a mail tail piece. It also connects to your inlet and outlet of your pipe leading to the inlet and outlet of your Superfalls pump. All unions are slip/slip. Complete unions are used to create a removable joint in a piece of pipe.
 |
||
| 03-UNS100 | 1'' HALF UNION SET | $10.00 |
| 03-UNS150 | 1-1/2'' HALF UNION SET | $12.00 |
| 03-UNS200 | 2'' HALF UNION SET | $15.00 |
| 03-UNS250 | 2-1/2'' HALF UNION SET | $18.00 |
 |
||
| 03-UNC150 | 1-1/2'' COMPLETE UNION | $16.00 |
| 03-UNC200 | 2'' COMPLETE UNION | $22.00 |
| 03-UNC250 | 2-1/2'' COMPLETE UNION | $29.00 |
| 03-UNC300 | 3'' COMPLETE UNION | $38.00 |
| 03-UNC400 | 4'' COMPLETE UNION | $89.00 |
| FITTING SIZE | COUPLING CPL-SIZE | CAP CAP-SIZE | PLUG PLG-SIZE | ELBOW S X S LSS-SIZE | ELBOW S X FIPT LST-SIZE | TEE ALL SLIP TSSS-SIZE |
| 1/2" | 03-CPL005 $0.28 | 03-CAP005 $0.38 | 03-PLG050 $0.90 | 03-LSS050 $0.42 | 03-LST050 $0.52 | 03-TSSS05 $0.52 |
| 3/4" | 03-CPL075 $0.38 | 03-CAP075 $0.43 | 03-PLG075 $1.06 | 03-LSS075 $0.47 | 03-LST075 $0.59 | 03-TSSS75 $0.59 |
| 1" | 03-CPL010 $0.66 | 03-CAP010 $0.68 | 03-PLG010 $1.27 | 03-LSS010 $0.85 | 03-LST010 $1.12 | 03-TSSS10 $1.12 |
| 1 1/2" | 03-CPL015 $0.97 | 03-CAP015 $1.06 | 03-PLG015 $1.72 | 03-LSS015 $1.60 | 03-LST015 $2.06 | 03-TSSS15 $2.12 |
| 2" | 03-CPL020 $1.50 | 03-CAP020 $1.27 | 03-PLG020 $2.70 | 03-LSS020 $2.50 | 03-LST020 $5.35 | 03-TSSS20 $3.08 |
| 2 1/2" | 03-CPL025 $3.30 | 03-CAP025 $4.08 | 03-PLG025 $4.62 | 03-LSS025 $7.60 | 03-LST025 $13.21 | 03-TSSS25 $10.18 |
| 3" | 03-CPL030 $5.17 | 03-CAP030 $4.48 | 03-PLG030 $6.11 | 03-LSS030 $9.10 | 03-LST030 $19.81 | 03-TSSS30 $13.36 |
| 4" | 03-CPL040 $7.46 | 03-CAP040 $10.18 | 03-PLG040 $13.82 | 03-LSS040 $16.28 | 03-LST040 $30.04 | 03-TSSS40 $24.16 |
| 6" | 03-CPL060 $23.62 | 03-CAP060 $24.37 | N/A | 03-LSS060 $51.77 | N/A | 03-TSSS60 $81.34 |
| FITTING SIZE | MALE ADAPTER | FEMALE ADAPTER |
CLOSE NIPPLE (close-to 60'' available) |
TEE/SSS | CROSS |
| 1/2" | 03-MAD050 $..38 | 03-FAD050 $.47 | 03-CN0050 $.30 | 03-TSS050 $ .52 | 03-CRS050 $1.60 |
| 3/4" | 03-MAD075 $.42 | 03-FAD075 $.59 | 03-CN075 $.35 | 03-TSS075 $.59 | 03-CRS075 $2.65 |
| 1" | 03-MAD100 $.74 | 03-FAD100 $.68 | 03-CN0100 $.42 | 03-TSS100 $1.12 | 03-CRS100 $3.30 |
| 1 1/2" | 03-MAD150 $1.22 | 03-FAD150 $1.22 | 03-CN0150 $1.21 | 03-TSS150 $2.12 | 03-CRS150 $4.94 |
| 2" | 03-MAD200 $1.61 | 03-FAD200 $1.64 | 03-CN0200 $1.58 | 03-TSS200 $3.08 | 03-CRS200 $7.28 |
| 2 1/2" | 03-MAD250 $4.73 | 03-FAD250 $4.15 | 03-CN0250 $2.87 | 03-TSS250 $10.18 | N/A |
| 3" | 03-MAD300 $6.92 | 03-FAD300 $5.58 | 03-CN0300 $3.67 | 03-TSS300 $13.36 | N/A |
| 4" | 03-MAD400 $8.83 | 03-FAD400 $9.25 | 03-CN0400 $5.59 | 03-TSS400 $24.16 | N/A |
| 6" | 03-MAD600 $23.03 | N/A |
N/A |
03-TSS600 $81.34 | N/A |
Call for sizes and prices of: Reducing Tee's, Street Ell's, Reducing Ell's, FIPT Tee's, 45 Ell's, Plugs, Couplings, reducer couplings and reducer bushing.
|
BARBED FITTINGS | |
| FITTING SIZE | BARBED MALE ADAPTER | BARBED FEMALE ADAPTER |
BARBED ELBOW (90) |
BARBED TEE | BARBED CROSS |
| 1/8'' | N/A | N/A | N/A | 03-BT0018 $.39 | N/A |
| 3/16'' | N/A | N/A | N/A | 03-BT0316 $.49 | N/A |
| 1/4'' | N/A | N/A | N/A | 03-BT0025 $.49 | N/A |
| 3/8'' | N/A | N/A | N/A | 03-BT0038 $.99 | N/A |
| 1/2" | 03-BMA050 $.68 | 03-FBA050 $2.99 | 03-BE9050 $1.34 | 03-BT0050 $1.46 | 03-BCR050 $3.84 |
| 3/4" | 03-BMA075 $.82 | 03-FBA075 $3.25 | 03-BE9075 $1.64 | 03-BT0075 $1.60 | 03-BCR075 $3.84 |
| 1" | 03-BMA100 $.85 | 03-FBA100 $3.61 | 03-BE9100 $1.81 | 03-BT0100 $2.08 | 03-BCR100 $4.79 |
| 1 1/4'' | 03-BMA125 $1.34 | 03-FBA125 $4.43 | 03-BE9125 $2.03 | 03-BT0125 $3.24 | 03-BCR125 $8.09 |
| 1 1/2" | 03-BMA150 $1.51 | 03-FBA150 $5.63 | 03-BE9150 $2.40 | 03-BT0150 $3.67 | 03-BCR150 $9.20 |
| 2" | 03-BMA200 $2.88 | 03-FBA200 $9.49 | 03-BE9200 $3.36 | 03-BT0200 $7.25 | 03-BCR200 $18.11 |
Call for sizes and prices of: Reducing Tee's, Combination Tee's, Reducing Elbows, Side outlet Tee's, Plugs, Reducing Cross, Reducing couplings and couplings.
|
|
|
 |
Now you can simplify the job of installing your ponds, waterfalls, filters, etc. Many contractors have made their jobs easier by simply unrolling this flexible pipe or hose into a ditch, around corners, over bumps, etc. without any fittings such as 90's, 45's, etc. Flexible PVC pipe is ideal for use in low pressure applications, and should not be used in medium to high pressure plumbing systems where pressure increases may exceed 10 - 15 psi. For easy pond building (and energy efficiency), use Flexible PVC pipe, Superfalls energy efficient low head pumps, and Aquadyne low head bio-filters. Available in sizes from 1 inch diameter to 6 inch diameter, this material is glued with our flex glue, 03-FLXG16 or 03-FLXG32 (32 oz. size). This pipe should be used with low head applications only, ie. 15 psi or less, and will greatly simplify pond construction and reduce time. Available in gray, 50 ft or 100 ft rolls, or smaller quantities, and all of the popular diameters. Use standard PVC fittings with the flexible glue below. |
|
ITEM |
*
Note: Remote cable operation of valve (as when buried) is possible with the
attached cable operator in these valves. Manual operation is with supplied
handle. 